Quick Delivery PI ROPE Wheelset 29″ FADE 6-Hole Lucky Jack 6TERS SLS3 26/26 mm | Black Premium Edition

PI ROPE wheelset 29″ FADE 6-hole Lucky Jack 6TERS SLS3 26/26 mm | Black Premium Edition

An ultra-light XC wheelset with black textile spokes? So far, there have been many approaches from well-known manufacturers, but all of them have produced unsatisfactory results. The young and extremely innovative think tank PI ROPE from Chemnitz, Saxony, has made the impossible possible in cooperation with the Technical University of Chemnitz. The result is a textile spoke made of braided Vectran synthetic fibers.
The material is extremely robust, resistant to aging and weathering, and has better mechanical properties than its steel counterpart. The tensile strength and damping is many times higher, but the weight of the fibers is five times lower. These are optimal prerequisites for a very light, but nevertheless hard-wearing wheel, as the rotating masses are minimized in the important outer areas and the flexibility of the Vectran textile spokes prevents permanent plastic deformation at high peak loads.

Thanks to the new, black PI PROTECT coating of the Vectran yarn before the braiding process, the properties of the textile spokes are improved. The treated surface not only looks good, it also offers better UV protection and reduces the impact of adverse weather conditions.
In addition, the abrasion resistance against external damage, such as that caused by stones and branches on the trail, increases. Mechanical loads that occur are better absorbed and ensure greater durability. The resulting increase in rigidity is particularly noticeable when cornering. Another plus, the processing of the textile spoke could be qualitatively optimized again.

The hubs, which can accommodate the special ends of the PI ROPE spokes, were specially developed in cooperation with the well-known component manufacturer NEWMEN. The long-lasting bearings are pressed in precisely and stress-free at the factory, so that the often tedious adjustment of the axial bearing clearance is no longer necessary. This has increased the level of user-friendliness. The design of the freewheel is completely different from the previous model. The goal was low noise. The result was the FADE ratchet system. 3 pawls engage in a new type of tooth profile. To increase durability, the diameter was enlarged and the individual pawls were short and wide. Thus, the resulting forces are distributed over a larger area and the hub is even released for e-bikes and tough enduro use.

The installed DUKE Lucky Jack SLS3 6TERS rims are the new flagships among the XC rims from the French manufacturer. Duke has managed to improve the Lucky Jack compared to the SLS2 version. In doing so, they have once again pushed the apparently technically possible limits. A 26 mm wide rim with a weight of only approx. 290g is a direct challenge to the competition.
How did the French do this? They took a closer look at the individual elements of the rim and looked for optimization options. In addition to small material savings in some places, a new resin was used. This not only made it possible to slim down, but also to increase impact resistance at the same time. Similar to the SLS2 production process, post-processing or painting is not necessary here either.
The rim has an asymmetrical profile, which allows the spokes to have a more even angle of attack. This optimization of the spoke angle brings with it a multitude of advantages. The spoke tension on both sides can be better adjusted to each other, which is beneficial to the durability of the spokes and the entire wheel. The lateral stiffness, which is normally directional, is also adjusted so that the impeller itself becomes stiffer. Technical specifications:

Area of intended use : cross country, marathon, e-bike
Wheel size: 29″ (ETRTO: 622 x 25.6 mm)
Rim Type: Clincher (clincher and folding)
Brake type: only for disc brake
Material hub: aluminum, steel
Material rim: UD carbon
Material spoke: Vectran synthetic fiber
Inner width rim: 25.6 mm
Outer width rim: 31.5 mm
Rim Height: 19mm
Number of holes: 28 holes (per rim)
Spokes: 56x Pi ROPE Vectran PI Protect textile spokes / straight pull (black)
Axle standard front: axle type mm BOOST
Rear axle type standard: 12×148 mm BOOST
Brake disc mount: 6-hole
Front bearing : Industrial deep groove ball bearing
bearing at the back: industrial deep groove ball bearing
Freewheel compatibility: 9-, 10-, 11-speed MTB Shimano | SRAM, 11-, 12-speed SRAM XD or 12-speed Shimano Micro Spline
Freewheel type: 3 pawls, 36 detents
recommended tire width: 1.3″ – 2.4″ (34-60 mm)
Maximum tire pressure: max. 2.5 bar (at 2.1″ tire width)
Maximum system weight: 110 kg (rider, bike, clothing and possibly luggage)
tubeless capable: yes
Valve hole: Presta valve (SV)
Finish rims: UD carbon, satin finish
Color spokes: black
Color hubs: black, logos – grey

Weight according to the manufacturer: 1150g
Weight weighed: Scope of delivery:

1x PI ROPE wheelset 29″ FADE 6-hole Lucky Jack 6TERS SLS3 26/26 mm | Black Premium Edition
1x spare spoke
1x tube of care oil for textile spokes